Mercedes S-Class W-140

In 1991-1999 editions

Repair and enterprise of the car


Mercedes S-Class
+ Mercedes Benz cars of the class S (W-140)
+ operation manual
+ Routine maintenance
- Motor
   Check of compression in the motor cylinder
   Check of the motor by means of vacuum meter
   Serpantinnogo belt of an incentive of auxiliary devices
   + 6-cylinder petrol engines (M104.944 and M104.990/994)
   + 8-cylinder petrol engines (M119.970/981 and M119.971/981)
   - 12-cylinder petrol engines (M120.980/982)
      The filter for purification of air - a device detail
      Covers of the heads of the block of cylinders
      Removal and device of the pipeline of access
      Removal and device of a final collector
      The rezirkuljazii gate of the working gases - a device detail
      Air transfer pump
      Removal and device of the top halls kryschek
      Heads of the block of cylinders
      Removal and device of a cover of a chain of an incentive of GRM
      Compensation of a chain of an incentive of GRM
      GRM incentive - the general information, service of components
      Natjaschitel of a chain of an incentive of GRM
      Regulator of a wave of curves
      Removal and device of waves of curves
      Check of phases of management of gas exchange
      Check and regulation of provision of waves of curves
      Compensation judging banks of gates
      Measurement of diameters of cylinders
      Removal and device of pistons
      Check of poles of an instinct
      Removal and device of a bent shaft
      Removal and device of a peel kartera of the motor
      The touch switch of level of oil - a device detail
      The fat pump - a design and details of the device
   + 6-cylinder diesel engines (OM603.971)
   + 6-cylinder diesel engines (OM606.961)
+ cooling systems, heating
+ systems of power supply and edition
+ electric equipment of the motor
+ gear shifting boxes
+ Awtomatitscheckaja transmission
+ connection
+ brake system
+ Aufhängung and management
+ body
+ electric onboard equipment


Removal and device of a cover of a chain of an incentive of GRM

Removal

GRM incentive chain cover device details


 EXECUTION ORDER

1. Accept cover halls.
2. Accept the pump of the cooling system (2).
3. Accept the filter for purification of air with the measuring device of an air current.
4. Accept the air pump (9).
5. Accept the generator (13).
6. Install the piston of the first cylinder in situation 30 ° after WMT.
7. Designate GRM incentive chain arrangement concerning starlets of waves of curves.
8. Accept glass of a bent shaft by means of the krutilnych muffler of fluctuations.

Bolts of strengthening of glass of the tax pump (are shown by an arrow)

10 — glass of the tax pump
12 — pompovy installation
14 — a bolt
21 — Priwodnoj of belts


Bolts of strengthening of the tax pump (shooter) and contact plugs of the electric leading device of sensors of WMT (l / 1) and (L1/2)

7 — GRM incentive chain cover
12 — pompovy installation


 EXECUTION ORDER

1. Prevent glass (10) wheels pumps (12) and accept it, establish a belt of an incentive of the generator (21) about glass (10), establish a bolt (14) and weaken bolts of underground mining.
2. Pull out bolts of strengthening of the tax pump (12) and strengthen the pump with the connected listeners along with it. On motors by means of WMT sensor you prevent sensors (L1/1) and (L1/2) from GRM incentive chain cover.

Position of the filter of the air pump (4); bolts (15 and (16) strengthenings of the basic carrier (3) air pumps / generators

4 — the pump
15, 16 — bolts
3 — strengthening of the basic carrier


 EXECUTION ORDER

1. Prevent the filter of the air pump (4) and accept it.
2. Prevent bolts (15) and (16) and accept the carrier at (3) air pumps / generators.
3. Prevent GRM incentive chain natjaschitel.
4. Prevent bolts (17), (18 and (19) and accept GRM incentive chain cover.

Device

8 — Uplotnitelnyje of a ring
20 — the Directing plug


 EXECUTION ORDER

1. Wipe and grease germetikom uplotnitelnyje of a surface (shooter) of the fat highway of a cover of a chain of an incentive of GRM (7).
2. Wipe uplotnitelnyje of a surface of a cover of a chain of an incentive of GRM (7) and the block of cylinders. Grease uplotnitelnyje of a surface of the fat highway of a cover of a chain of an incentive of GRM (7) germetikom 002 989 73 20 10.
3. Replace uplotnitelnyje of a ring (8).
4. Establish a cover of a chain of an incentive of GRM (7).
5. Tighten strengthening bolts (17 and (18) from the first.
6. Check association of color signs (shooter) for chains of an incentive of GRM and on starlets of waves of curves.
7. Establish GRM incentive chain natjaschitel.
8. The device as it should be, carried out down removals will be farther.