Mercedes S-Class W-140

In 1991-1999 editions

Repair and enterprise of the car


Mercedes S-Class
+ Mercedes Benz cars of the class S (W-140)
+ operation manual
+ Routine maintenance
- Motor
   Check of compression in the motor cylinder
   Check of the motor by means of vacuum meter
   Serpantinnogo belt of an incentive of auxiliary devices
   + 6-cylinder petrol engines (M104.944 and M104.990/994)
   + 8-cylinder petrol engines (M119.970/981 and M119.971/981)
   - 12-cylinder petrol engines (M120.980/982)
      The filter for purification of air - a device detail
      Covers of the heads of the block of cylinders
      Removal and device of the pipeline of access
      Removal and device of a final collector
      The rezirkuljazii gate of the working gases - a device detail
      Air transfer pump
      Removal and device of the top halls kryschek
      Heads of the block of cylinders
      Removal and device of a cover of a chain of an incentive of GRM
      Compensation of a chain of an incentive of GRM
      GRM incentive - the general information, service of components
      Natjaschitel of a chain of an incentive of GRM
      Regulator of a wave of curves
      Removal and device of waves of curves
      Check of phases of management of gas exchange
      Check and regulation of provision of waves of curves
      Compensation judging banks of gates
      Measurement of diameters of cylinders
      Removal and device of pistons
      Check of poles of an instinct
      Removal and device of a bent shaft
      Removal and device of a peel kartera of the motor
      The touch switch of level of oil - a device detail
      The fat pump - a design and details of the device
   + 6-cylinder diesel engines (OM603.971)
   + 6-cylinder diesel engines (OM606.961)
+ cooling systems, heating
+ systems of power supply and edition
+ electric equipment of the motor
+ gear shifting boxes
+ Awtomatitscheckaja transmission
+ connection
+ brake system
+ Aufhängung and management
+ body
+ electric onboard equipment


Check of phases of management of gas exchange

Phases of management of gas exchange of the motor of the M120.980 series

Check the digital name of waves of curves. Kodes are beaten out on schejke of the 3rd camp or on a flange

Waves of curves of access

 EXECUTION ORDER

1. Prowernite a bent shaft by means of a key in such a way that nossiki of small fists of waves of curves of access were upward directed.

2. Establish a bolt (2) ziferblatnogo of the measuring device with the plug of a slice (4) on uplotnitelnuju a surface of a cover of the head of the block of cylinders of the tested wave of curve cylinders (1) or (7).
3. Connect ziferblatnyj the measuring device (1) with the floor (3) (80 mm) on a bolt (2) in such a way that the floor (3) was established vertically on the hydro-compensator (shooter) with a suit of 3 mm.
4. Check ease of shift of the floor (3).
5. Establish the arrow ziferblatnyj the measuring device (1) in "0".
6. Turn a bent shaft of a key in the direction of Drehens of the motor until the measuring device (1) does not show raising of the gate on 2 mm. In this situation you check "a corner of Aufmachens of the inlet valve after WMT" on the krutilnych muffler of fluctuations.

Final waves of curves

 EXECUTION ORDER

1. Prowernite a bent shaft by means of a key in such a way that nossiki of small fists of final waves of curves were upward directed.
2. Establish a bolt (2) ziferblatnogo of the measuring device with the plug of a slice (4) on uplotnitelnuju a surface of a cover of the head of the block of cylinders of the tested wave of curve cylinders (1) or (7).
3. Connect ziferblatnyj the measuring device (1) with the floor (3) (80 mm) on a bolt (2) in such a way that the floor (3) was established vertically on the hydro-compensator (shooter) with a suit of 3 mm.
4. Check ease of shift of the floor (3).
5. Establish an arrow of the measuring device (1) in "0".
6. Turn a bent shaft of a key in the direction of Drehens of the motor until the measuring device does not show raising of the gate on 2 mm. In this situation you check "a corner of Aufmachens of the locking valve before NMT" on the krutilnych muffler of fluctuations.