Mercedes S-Class W-140

In 1991-1999 editions

Repair and enterprise of the car

Heads of the block of cylinders

Removal

Details of the device of the left head of the block of cylinders


11 — a bolt 12 — the carrier 13 — a cover of the camp of a wave of curves 16 — the head of the block of cylinders 18 — transferring 19 — the listener of ventilation 22 — sewer

Details of the device of the left head of the block of cylinders


10 — cutting of the cooling system 18 — transferring

Details of the device of the right head of the block of cylinders


1, 5 — listeners of transfer of air 6 — the Directing pipe of the list of level of oil 7 — the list of level of AT oil 8 — the listener of ventilation of kartera 9 — cutting of the cooling system

Details of the device of the right head of the block of cylinders


11 — a bolt 12 — the carrier 13 — a cover of the camp of a wave of curves 14 — the head of the block of cylinders 17 — transferring

Removal of the heads of the block of cylinders of waves of curve and final collectors is possible only after full cooling of the motor!

EXECUTION ORDER

1. Install the piston of the first cylinder in situation 30 ° after WMT. In this provision of a wave of curves can be turned without soudarenija of gates and pistons.

2. Designate mutual position of starlets of waves of curves concerning GRM incentive chain.

3. On the left head of the block of cylinders: accept the listener (5) at ventilation of kartera.

4. On the left head of the block of cylinders you accept a finger (1) of the judging lever by means of a tiskalshchik and an insert of a slice.

5. Prevent the air pump podmeschiwanija filter in an exhaust and accept it.
6. Prevent listeners of transfer of air from the air pump podmeschiwanija in an exhaust. On the right head of the block of cylinders there is a bolt on the head, a bolt on the carrier of the motor and a bolt on a motor kartera peel. On the left head of the block of cylinders: it is a bolt - on the head, - on the block of cylinders as a final collector and - on the left carrier of the motor below.

7. Prevent the judging pipe of the list of level of oil. On the right head of the block of cylinders you prevent the judging pipe (7) schtschupa of measurement of the ATF level from the block of cylinders and transmission.
8. On the right head of the block of cylinders you prevent also the listener of ventilation of kartera (8) from the head of the block of the cylinder (shooter).

9. Prevent a final collector in thinking out the block of cylinders.

10. Pull together the cooled liquid of the block of cylinders. For this purpose you prevent traffic jams (shooter) with a condensation. Moment of a delay of 30 Nanometers.

11. As it should be, down it is shown on an illustration acting, you weaken bolts of strengthening of the head of the block of cylinders as it should be, down a delay order, with 14.

12. Establish Hebehenkel on the head of the block of cylinders. Prevent a cover of the 1st camp of a final wave of curves on the right head of the block of cylinders and install the carrier with the judging banks (18a). Prevent a cover of the 2nd camp of a final wave of curves on the left head of the block of cylinders and install the carrier with the judging banks (18a). Moment of a delay of 21 Nanometer.

13. Connect the elevator to the carrier and a back point of support of the motor, lift and accept the head of the block of cylinders.

Do not damage natjaschnoj and directing levers!

14. Check the contact surface of the head of the block of cylinders.

Device

EXECUTION ORDER

1. Establish transferring. Will pay attention to an arrangement of the judging fingers (1) and judging to bank (2) for an arrangement of the head of the block of cylinders.
2. Check bolts of strengthening of the head of the block of cylinders. 3. Grease a part of a slice of bolts and the contact surfaces of the heads of the block of cylinders with engine oil and establish them.
4. Tighten strengthening bolts in strictly certain order.
5. The device as it should be, made down removals will be farther. Check the device of waves of curves. Check liquid level in AT and their dolejte if it is necessary.