Mercedes S-Class W-140

In 1991-1999 editions

Repair and enterprise of the car



Mercedes S-Class
+ Mercedes Benz cars of the class S (W-140)
+ operation manual
+ Routine maintenance
- Motor
   Check of compression in the motor cylinder
   Check of the motor by means of vacuum meter
   Serpantinnogo belt of an incentive of auxiliary devices
   + 6-cylinder petrol engines (M104.944 and M104.990/994)
   + 8-cylinder petrol engines (M119.970/981 and M119.971/981)
   - 12-cylinder petrol engines (M120.980/982)
      The filter for purification of air - a device detail
      Covers of the heads of the block of cylinders
      Removal and device of the pipeline of access
      Removal and device of a final collector
      The rezirkuljazii gate of the working gases - a device detail
      Air transfer pump
      Removal and device of the top halls kryschek
      Heads of the block of cylinders
      Removal and device of a cover of a chain of an incentive of GRM
      Compensation of a chain of an incentive of GRM
      GRM incentive - the general information, service of components
      Natjaschitel of a chain of an incentive of GRM
      Regulator of a wave of curves
      Removal and device of waves of curves
      Check of phases of management of gas exchange
      Check and regulation of provision of waves of curves
      Compensation judging banks of gates
      Measurement of diameters of cylinders
      Removal and device of pistons
      Check of poles of an instinct
      Removal and device of a bent shaft
      Removal and device of a peel kartera of the motor
      The touch switch of level of oil - a device detail
      The fat pump - a design and details of the device
   + 6-cylinder diesel engines (OM603.971)
   + 6-cylinder diesel engines (OM606.961)
+ cooling systems, heating
+ systems of power supply and edition
+ electric equipment of the motor
+ gear shifting boxes
+ Awtomatitscheckaja transmission
+ connection
+ brake system
+ Aufhängung and management
+ body
+ electric onboard equipment



Removal and device of a peel kartera of the motor

Motor kartera peel device details

Removal

 EXECUTION ORDER

1. Accept a generator incentive belt.
2. Accept the filter for purification of air with the measuring device of an air current
3. Exclude the negative line of the battery.
4. Accept the lower protective sign of the motor.
5. Pull together engine oil.
6. Exclude the plug of the line of a sensor of pressure of oil upon masloraspredelitele (18).
7. Prevent the AT (17) pipelines from a peel (20).
8. Prevent the air podmeschiwanija pipelines in an exhaust (15) in the lower part of a peel (18) and you deceive also the right carrier of the motor.
9. Prevent masloraspredelitel (18).
10. Exclude the plug (2) from a sensor of level of oil (S43) in a peel (20).
11. Prevent bolts (14) strengthenings of a peel.
12. Accept the forward stabilizer of cross immunity.
13. Accept forward feathers (21).
14. Prevent the muffler (27) below.
15. Prevent both lower forward support of the motor (09) from forward carriers (28).
16. Install the elevator (060) motors.
17. Priwernite Hebehenkel of the motor ahead and behind.
18. Prevent the judging pipe of the list of level of oil (3) from a cover of the head of the block of cylinders.
19. Prevent a board (26) of a joint of a tax wave (25) and strengthen it along with it.
20. Exclude a joint of a tax wave (25).
21. Lift the motor by means of the elevator (070).
22. Be lowered behind a cover of bolts (22).
23. Prevent bolts (22) Forward support (28).
24. Lower a forward part of the motor (28) until perhaps the peel is not lowered.
25. Accept the generator (13).
26. Prevent the AT (16) pipelines and (17), accept the fat heater (11), the peel conditioner compressor.
27. Prevent the judging pipe schtschupa of measurement of level of oil (3) from a peel.
28. Prevent bolts of strengthening of a peel.
29. Lower a peel (20) and accept it, translated forward.
30. Replace transferring (21).

Device

The device will be as it should be, made down removals.

Order of a delay and weakening of bolts of strengthening of a peel of the motor.

1 — M6x22 bolts
2 — M6x50 bolt
3 — M6x85 bolts
4 — M8x40 bolts
5 — M10x40 barges