Mercedes S-Class W-140

In 1991-1999 editions

Repair and enterprise of the car


Mercedes S-Class
+ Mercedes Benz cars of the class S (W-140)
+ operation manual
+ Routine maintenance
- Motor
   Check of compression in the motor cylinder
   Check of the motor by means of vacuum meter
   Serpantinnogo belt of an incentive of auxiliary devices
   + 6-cylinder petrol engines (M104.944 and M104.990/994)
   + 8-cylinder petrol engines (M119.970/981 and M119.971/981)
   - 12-cylinder petrol engines (M120.980/982)
      The filter for purification of air - a device detail
      Covers of the heads of the block of cylinders
      Removal and device of the pipeline of access
      Removal and device of a final collector
      The rezirkuljazii gate of the working gases - a device detail
      Air transfer pump
      Removal and device of the top halls kryschek
      Heads of the block of cylinders
      Removal and device of a cover of a chain of an incentive of GRM
      Compensation of a chain of an incentive of GRM
      GRM incentive - the general information, service of components
      Natjaschitel of a chain of an incentive of GRM
      Regulator of a wave of curves
      Removal and device of waves of curves
      Check of phases of management of gas exchange
      Check and regulation of provision of waves of curves
      Compensation judging banks of gates
      Measurement of diameters of cylinders
      Removal and device of pistons
      Check of poles of an instinct
      Removal and device of a bent shaft
      Removal and device of a peel kartera of the motor
      The touch switch of level of oil - a device detail
      The fat pump - a design and details of the device
   + 6-cylinder diesel engines (OM603.971)
   + 6-cylinder diesel engines (OM606.961)
+ cooling systems, heating
+ systems of power supply and edition
+ electric equipment of the motor
+ gear shifting boxes
+ Awtomatitscheckaja transmission
+ connection
+ brake system
+ Aufhängung and management
+ body
+ electric onboard equipment


Compensation of a chain of an incentive of GRM

Look also has GRM incentive - the general information, service of components extended


Compensation of a chain of an incentive of GRM

GRM incentive chain A — Rassojedinenije
In — Saklepywanije of a chain of an incentive of GRM by means of the connecting member
6 — thickness of a mezhdudisk 7a = 1.6 mm, thickness of an external disk 8b = 1.2 mm


 EXECUTION ORDER

1. Be lowered top covers (30) and (30a).
2. Be lowered by GRM incentive chain natjaschitel.
3. Accept spark plugs.
4. Rassojedinite GRM incentive chain.
5. Cover GRM cover from material.

chain rassojedinenije

 EXECUTION ORDER

1. Screw up a persistent spindle (02) together with a persistent finger (02a) in application (03).
2. Establish application (03) on a chain.
3. Screw up a persistent spindle (02) until the persistent finger (02a) does not oppose in a chain finger.
4. Screw up a persistent spindle (02) and wypressujte a chain finger.
5. Prevent a persistent spindle (02) and accept application (03). Pull out a finger from application (03).

Installation of a chain

 EXECUTION ORDER

1. Connect a new chain (5) too as before (4) by means of the connecting member who exists from the lock (6), disks (7), a mezhdudisk and covers (8).

2. Prowernite a bent shaft in the direction of Drehens of the motor by means of a key. Consider in a chain from (5) hand on the starlet of the right final wave of curves (9) and pull out the lower end of a chain (4) outside from GRM incentive chain cover.
3. Continue to turn a bent shaft of the motor until an opportunity does not appear to connect both the end of a new chain of the connecting member.
4. Exclude an old chain and accept the connecting member.
5. Connect a new chain of the connecting member and a mezhdudiska (thickness of 1.6 mm).
6. Establish a persistent detail of smetkoj (F1) in saklepotschnyj the tool and screw up a bolt (28).
7. Establish a persistent detail of smetkoj (D5) in saklepotschnyj the tool.
8. Establish an external disk (11) (thickness of 1.2 mm) in a persistent detail (D5).
9. Establish kernels (shooter) on fingers of the connecting member. Screw up a spindle (06) to full resistance. At wworatschiwanii are convinced that fingers of the connecting member did in opening in a disk right thing.
10. Establish a persistent detail of smetkoj (D5).
11. Establish saklepotschnyj the tool in the middle disks.
12. Tighten a spindle (06). Moment of a delay of 30-35 Nanometers.

Fingers of the connecting member of saklepywajutsja separated.

13. Check quality of saklepywanija, repeat process as a last resort.