Mercedes S-Class W-140

In 1991-1999 editions

Repair and enterprise of the car


Mercedes S-Class
+ Mercedes Benz cars of the class S (W-140)
+ operation manual
+ Routine maintenance
+ motor
+ cooling systems, heating
+ systems of power supply and edition
+ electric equipment of the motor
+ Gear shifting boxes
- awtomatitscheckaja transmission
   Specifications
   Search of defects - the general information
   - Automatic transmission 722.5
      Removal, check of a state and device of the reformer of Drehens (hydro-transformer)
      Removal and device of the centrifugal regulator
      Removal and device of the touch switch of blocking of a starter (solution of start)
      Vacuum knot - a device detail
      Removal, service and the device of the repeated pump (AT to No. 3652931)
      Removal and device of a forward cover of the repeated pump
      Removal and device of the LB3 piston
      Removal and device of a back cover of transmission
      Discussion and installation of installation of AT valves
      Discussion and installation of transmission
      The device and check of freedom of action in Mehrscheibenbremse B3
      Measurement of freedom of action in B1 brake
      Connection of the raising transfer
      Removal, the device and check of components of a brake of BS of the raising transfer and the KS connection
      Discussion and installation of mufty of the free movement
      Discussion and installation of planetary mechanisms
      Discussion and installation of the K1 connection
      K2 connection
      Gear shifting Selektors lever
   + Automatic transmission 722.6
+ connection
+ brake system
+ Aufhängung and management
+ body
+ electric onboard equipment


Discussion and installation of the K1 connection

Discussion

K1 connection design

1 — support of external Disks
2 — the piston
3 — a feather
4 — the Rise-strong plug
5, 11, 16 — blocking rings
6 — Internal Disk
7, 8, 10 — External Disks

12, 13, 17 — Uplotnitelnyje of a ring
15 — a feather of glasses
18 — the Directing piston ring
19 — a sphere
020 — tiskalshchik
A — freedom of action in the K1 connection


 EXECUTION ORDER

1. Accept a blocking ring (11) from external support of external Disks at (1) connection.
2. Take Disks (6), (7), (8), (10) and a feather of glasses (15 c). Check Disks for lack of sale and damages.
3. Establish a tiskalshchik (020) on rise - the strong plug (4) and squeeze them until the blocking ring (5) is not released.
4. Accept a blocking ring (5).
5. Accept rise - the strong plug (4) from a feather (3).
6. Pull out the piston (2) to support (1).
7. Be lowered by ring uplotnitelnyje (12 and (13) from the piston.
8. Accept a blocking ring (16) from support of external Disks (1).
9. Accept the judging ring of the piston (18).
10. Be lowered by uplotnitelnoje a ring (17).

Installation

 EXECUTION ORDER

1. Establish in a new way uplotnitelnoje a ring (17).
2. Establish the judging ring of the piston (18).
3. Establish a blocking ring (16) in support of external Disks (1).
4. Establish ring uplotnitelnyje (12 and (13) in the piston (2), - uplotnitelnyje have to be directed edgings down (in the direction of arrows); establish to bank (021 and (022) in support of external Disks (1).
5. Grease to bank and uplotnitelnyje of a ring transmissionnoj from liquid, install the piston (2) and sapressujte in support of external Disks (1) without Verkantung it is careful.
6. Establish rise - the strong plug (4) and a feather (3).
7. Establish a tiskalshchik (020) on rise - the strong plug (4) and squeeze them.
8. Establish a blocking ring (5).
9. Establish a feather of glasses (15) and Disks (6), (7), (8 and (10) in support of (1).
10. Establish a blocking ring (11). After the sapressujte device a blocking ring upward after the periphery up to the full device.

Check of freedom of action

Measure freedom of action of "A", regulate it by means of the choice of a blocking ring (11) necessary thickness (as a last resort watch an illustration 20.1). The nominal size of freedom of action "A" in the K1 connection lies in borders of the volume of 0.7-1.3 mm blocking rings of thickness of 2.0, 2.6 and 3.0 mm are issued.