Mercedes S-Class
+ Mercedes Benz cars of the class S (W-140)
+ operation manual
+ Routine maintenance
+ motor
+ cooling systems, heating
+ systems of power supply and edition
+ electric equipment of the motor
+ Gear shifting boxes
- awtomatitscheckaja transmission
Specifications
Search of defects - the general information
- Automatic transmission 722.5
Removal, check of a state and device of the reformer of Drehens (hydro-transformer)
Removal and device of the centrifugal regulator
Removal and device of the touch switch of blocking of a starter (solution of start)
Vacuum knot - a device detail
Removal, service and the device of the repeated pump (AT to No. 3652931)
Removal and device of a forward cover of the repeated pump
Removal and device of the LB3 piston
Removal and device of a back cover of transmission
Discussion and installation of installation of AT valves
Discussion and installation of transmission
The device and check of freedom of action in Mehrscheibenbremse B3
Measurement of freedom of action in B1 brake
Connection of the raising transfer
Removal, the device and check of components of a brake of BS of the raising transfer and the KS connection
Discussion and installation of mufty of the free movement
Discussion and installation of planetary mechanisms
Discussion and installation of the K1 connection
K2 connection
Gear shifting Selektors lever
+ Automatic transmission 722.6
+ connection
+ brake system
+ Aufhängung and management
+ body
+ electric onboard equipment
|
Connection of the raising transfer
Discussion Design of connection of the raising transfer
|
|
|
172 — the Mehrscheibenkupplung support
174, 179 — blocking rings
180 — Growth-strong of Disk
181, 185 — Radial networks |
182 — a feather
183 — pistons
184 — Uplotnitelnoje a ring
02 — a tiskalshchik |
|
|
|
1. Accept a blocking ring (174) from the Mehrscheibenkupplung (172) support.
2. Accept the Disks (176) block - (178) and a feather of glasses (175).
3. Establish a tiskalshchik (020) on rise - a strong disk (180) in such a way that the blocking ring (179) revealed.
4. Accept rise - a strong disk (180), a feather (182), radial network (181).
5. Pull out the piston (183) of an external support of connection (172). |
|
Installation and measurement of freedom of action in connection of the raising transfer Connection in duty
|
|
|
172 — the Mehrscheibenkupplung support
179 — a blocking ring
180 — Growth-strong of Disk
181, 185 — Radial network |
182 — a feather
183 — pistons
184 — Uplotnitelnoje a ring |
|
|
1. Install the plug (023) in a support of connection (172). Check radial network (185) and uplotnitelnoje a ring (184) for lack of sale, and if it is necessary, replace and grease them with transmissionnoj with liquid. At installation are convinced that edgings of networks (181 and (183) are upward located.
2. Install the piston (183).
3. Accept the plug (023). |
|
4. Establish to all to 18 or 19 feathers (182) in directing the piston (183).
5. Install the plug (024) in a support of connection (172).
6. Grease transmissionnoj network (131) with liquid and establish on rise - a strong disk (180).
7. Strengthen rise - a strong disk (180). |
|
| 8. Establish a blocking ring (179) on rise - a strong disk. Establish and strengthen a tiskalshchik (020). Establish a blocking ring (179). Are convinced of correctness of the device. |
|
|
Connection Disks device order
|
|
|
174 — a blocking ring
176 — a feather of glasses
178 — Internal Disks
177, 178 — External Disks |
|
|
|
| 1. Switching off you and you accept a tiskalshchik (020). Establish Disks of connection as it should be which is specified on the accompanying illustration, and establish in turn. In front of the device you put new Disks in transmissionnuju liquid approximately on 1 h. |
| 2. Accept the plug (024). |
|
| 3. Measure freedom of action of "S" and regulate from its blocking ring (174) if it is necessary. Thickness of a blocking ring of 2.0, 2.5, 3.0 and 3.5 mm. |
|
|
|