Mercedes S-Class
+ Mercedes Benz cars of the class S (W-140)
+ operation manual
+ Routine maintenance
- Motor
Check of compression in the motor cylinder
Check of the motor by means of vacuum meter
Serpantinnogo belt of an incentive of auxiliary devices
+ 6-cylinder petrol engines (M104.944 and M104.990/994)
+ 8-cylinder petrol engines (M119.970/981 and M119.971/981)
+ 12-cylinder petrol engines (M120.980/982)
- 6-cylinder diesel engines (OM603.971)
The filter for purification of air - a device detail
Compensation of a belt of an incentive of the generator
Removal and natjaschitelja device of a belt of an incentive of the generator
Final collector - a device detail
GRM incentive chain cover
Wave of curves
Removal and device of the head of the block of cylinders
Verification of the control provision of a wave of curves
Compensation of a chain of an incentive of GRM
GRM incentive - the general information, service of components
Natjaschitel of a chain of an incentive of GRM - a device detail
Removal and device of pistons
Check of a state and compensation of poles of an instinct
Measurement of diameters of cylinders
Removal and device of covers of cylinders
Check of a condition of a bent shaft
Removal and device of the starlet of a bent shaft
Removal and device of a peel kartera of the motor
The touch switch of level of oil - a device detail
Compensation of a chain of an incentive of the fat pump
Removal and device of the fat pump
Removal and device of a body of the fat filter
+ 6-cylinder diesel engines (OM606.961)
+ cooling systems, heating
+ systems of power supply and edition
+ electric equipment of the motor
+ gear shifting boxes
+ Awtomatitscheckaja transmission
+ connection
+ brake system
+ Aufhängung and management
+ body
+ electric onboard equipment
|
Wave of curves
Details of the device of a wave of curves
|
|
70 — the head of the block of cylinders
80, 81, 82 — covers of camps of a wave of curves
84, 132, 190 — bolts
84a, 189, 237 — glass
125 — covers of the head of the block of cylinders |
188 — the starlet of a wave of curves
224 — Natjaschitel of a chain of an incentive of GRM
400 — the Fat pump (on models with the self-settled Aufhängung) |
|
|
Code of a wave of curves the World Cup is beaten out on a flange along with it signs |
Removal
|
|
1. On motors with a turbocompressor you accept the listener of transfer of compressed air
2. Accept a cover of the head of the block of cylinders. |
3. Install the piston of the first cylinder in position of WMT.
|
|
Do not turn a bent shaft of the motor for a bolt of the starlet of a wave of curves and to the party, the Drehens directions down. |
|
|
4. Be lowered by GRM incentive chain natjaschitel.
5. On models with the self-settled Aufhängung you accept the fat pump. |
| 6. Unite signs on the starlet of a wave of curves and a chain of an incentive of GRM. |
|
| 7. Prevent a bolt of strengthening of the starlet of a wave of curves, in a wave of curves by means of a metal kernel it is supported. |
|
| 8. Accept the starlet of a wave of curves and allow swisnut chain. |
| 9. Prevent bolts of strengthening of kryschek (1), (5 and (6) camps of a wave of curves. Weaken bolts of strengthening of kryschek (2), (3), (4 and (7) alternately, after change of everyone. |
|
| 10. Accept a wave of curves. |
| 11. Accept blocking transferring (the regulator of axial freedom of action) and check its state. |
|
| 12. Accept the hydro-compensator. Check its state (optically) and if it is necessary, replace them. |
|
|
Device
|
|
| 1. Establish blocking transferring (the regulator of axial freedom of action) to the head of the block of cylinders. |
| 2. Oil a wave of curves with engine and establish it in the head of the block of cylinders in such a way that WMT was sharp above it is located. |
|
| 3. Establish covers of camps of a wave of curves and tighten bolts of its strengthening. First, you tighten covers (2), (3), (4 and (7) alternately, after change of everyone. Then you tighten bolts of strengthening of kryschek (1), (3 and (6) camps of a wave of curves. |
|
| 4. Establish the starlet of a wave of curves, a sign on it with a sign on a chain of an incentive of GRM it is combined. |
|
5. Establish GRM incentive chain natjaschitel.
6. Install the fat pump. |
| 7. Install the piston of the first cylinder in position of WMT and check association of signs. |
|
| 8. Establish a cover of the head of the block of cylinders. Conduct the motor and check lack of a vytecheniye. |
|
|
|