Mercedes S-Class W-140

In 1991-1999 editions

Repair and enterprise of the car


Mercedes S-Class
+ Mercedes Benz cars of the class S (W-140)
+ operation manual
+ Routine maintenance
+ motor
+ cooling systems, heating
+ systems of power supply and edition
+ Electric equipment of the motor
- Gear shifting boxes
   Specifications
   Removal and device of transmission gears
   Forward cover of transmission gears - a device detail
   Removal and device of a back cover of transmission gears
   - RKPP 717.438
      Removal and the device between kartera
      Check of freedom of action of the leading and intermediate waves
      Discussion and installation of the conducted wave
      Removal and the device of the key and conducted gear wheels
      Compensation of RKPP ball-bearings with No. 6 141 001
      Compensation of conic roller bearings of transmission gears to No. 6 141 000
      The gear shifting mechanism - a detail of the device of elements
   + RKPP 717.454
+ Awtomatitscheckaja transmission
+ connection
+ brake system
+ Aufhängung and management
+ body
+ electric onboard equipment


Removal and the device between kartera

Removal

Device details between kartera

37 — Kossosubaja a gear wheel of the 5th transfer
38 — Kossosubaja a speedometer incentive gear wheel
38a, 51 — Persistent glass
42, 50 — Uplotnitelnaja transferring
43, 43d, 45 — the External ring of the camp
43a — the ball-bearing
43b, 54, 57 — blocking rings
43c — the plug of roles
44 — transferring
46 — a wave of the reverse gear
47, 80 — bolts
48 — Kossosubaja a gear wheel of the reverse gear
49 — Between karter
52, 53 — Synchronisators ring

55 — the camp in the form of a needle
56 — Mufta Synchronisators
62 — a cover
70 — a camp finger
71 — a feather
72 — the plug
73 — Rise-strong transferring
74 — mother
75, 79 — switching levers
76 — the Internal lever of switching
77 — Uplotnitelnoje a ring
78 — a cover
A — transmission gears with kossosubymi from roller bearings (with 1 after 6 141 000)
In — transmission gears with ball-bearings (with 6 141 001)


 EXECUTION ORDER

1. Take transmission gears (with watch removal and the device of transmission gears left).
2. Take a back cover of transmission gears (with watch removal and the device of a back cover of transmission gears left).
3. Accept a gear wheel of a speedometer (38) and persistent glass (38a).
4. Accept a blocking ring (57), muftu Synchronisators (56), a ring of Synchronisators (38), a ring of Synchronisators (52), the camp in the form of a needle (55) and persistent glass (51).
5. Exclude kossosubuju a gear wheel (37) fifth transfers.
6. Prevent a bolt (47) strengthenings of a wave of transfer of a backing (46).
7. On transmission gears with kossosubymi from roller bearings you are diminished between karter (49).
8. On transmission gears with ball-bearings you exclude between karter (48).

Discussion

 EXECUTION ORDER

1. Accept the lever of gear shifting (79) for the 5th transfer and transfer of a backing, a cover (78) and uplotnitelnoje a ring (77). Replace uplotnitelnoje a ring (77).
2. Take a finger of the camp (70), a feather (71), the plug (72), rise - strong transferring (73) and the lever (75 c).
3. Wypressujte from between kartera a wave of transfer of a backing (46), kossosubuju a gear wheel of transfer of a backing (48).
4. On transmission gears with kossosubymi from roller bearings by means of wykolotki wypressujte external rings of camps (43 and (45).
5. Delay the plug of roles (43c), and wypressujte an external ring of the camp (43d) (on transmission gears ball-bearings) outside.
6. Pull out an external ring of the camp (43b) and wypressujte the ball-bearing (43a).
7. Measure removal of "a" between the contact surface and schelobkom of a ring of the camp of the conducted wave of transmission gears on as before and in a new way between karterach by means of a measuring latch (length about 300 mm). If the result of measurement which is taken on new between kartere does not correspond to result of measurement which is taken on old it is necessary to establish additional transferrings, - transferrings of thickness of 0.1, 0.3 and 0.5 mm are issued.
8. By means of Einstelinstruments sapressujte an external ring of the camp.
9. On transmission gears with kossosubymi from roller bearings you check a preliminary suit of conic roller bearings of the leading and intermediate waves.

Device

The device will be as it should be, carried out down removals.