Mercedes S-Class W-140

In 1991-1999 editions

Repair and enterprise of the car

Mercedes S-Class
+ Mercedes Benz cars of the class S (W-140)
+ operation manual
+ Routine maintenance
+ motor
+ cooling systems, heating
+ systems of power supply and edition
+ electric equipment of the motor
+ gear shifting boxes
+ awtomatitscheckaja transmission
- Connection
   + connection
   kardannyj wave
   - Power shafts
      Removal and device of a flange of a power shaft and radial persistent ball-bearing
      Removal, check and device of a power shaft
      Removal and SCHRUS device of power shafts and her protective caps
   + differential
+ brake system
+ Aufhängung and management
+ body
+ electric onboard equipment

Removal and device of a flange of a power shaft and radial persistent ball-bearing

Removal

Flange of a power shaft and radial persistent ball-bearing

EXECUTION ORDER

1. Accept a power shaft.
2. Accept Bremsdisk.
3. Be lowered at levels of stojanotschnoj of the brake system.
4. Pull out a flange of a power shaft (10) (at a certain support of a wheel).
5. Accept a blocking ring (9).
6. Accept the radial persistent ball-bearing (8) at a wheel support.
7. Pull out an internal ring of the camp from a flange of a power shaft.

Check

Check an axial and radial beating of a flange (10) power shafts. Admissible Höchstgr öße on one axis of ljufta of a flange 0.03 mm, a radial beating - also form 0.03 mm.

Device

The device will be as it should be, carried out down removals.

Flange of a power shaft

Removal

Removal of a flange of a power shaft

EXECUTION ORDER

1. Establish a screw thread to bolts (010j) in a flange (10) outside and priwernite to the carrier (010 g). 2. Establish a basic disk (010d) on a wheel support.
3. Establish prischimnuju a disk (010f) with prischimnym from a bolt (010b) the carrier and install on a basic drive (010d) again.
4. Establish the hydraulic press (010h) between persistent transferring (010f) and to the carrier (010 g). Prevent prischimnoj to bolts (010k) from the hydraulic press, then a bolt (010i) of the carrier until it does not concern prischimnogo the cylinder of the hydraulic press.
5. Screw up prischimnoj to bolts (010k) of the hydraulic press (the maximum moment of 40 Nanometers) until the flange of a power shaft is not accepted).
6. Fight from a hammer after the carrier (shooter).
7. If it becomes insufficient, pull out a bolt (010i) from the carrier.

Device

Device of a flange of a power shaft


7 — a wheel support 8 — Dwuchrjadnyj the radial persistent ball-bearing

Install a flange (10) on dwuchrjadnyj the radial persistent ball-bearing (8), Einstelinstrument (08a) - (08s), (08e) - (08i) using. Are convinced that few prischimnaja is correctly defined a disk (08s) on an internal ring of the camp (shooter).

dwuchrjadnyj, radial persistent ball-bearing

Removal of dwuchrjadnogo of the radial persistent ball-bearing


7 — a wheel support 08 — Dwuchrjadnyj the radial persistent ball-bearing 08a — bolts with mother 08b — tiskalshchik 08s — Persistent transferring is (not enough)

Dwuchrjadnogo device of the radial persistent ball-bearing


7 — a wheel support 8 — Dwuchrjadnyj the radial persistent ball-bearing 08a — bolts with mother 08b — tiskalshchik 08s — Persistent transferring is (not enough) 08e — Prischimnoj the camp